Filter results: Grounding Rods, Wire, and Accessories

HD V-Booms are the strongest mount in their class. They are designed to hold maximum loads in most wind speeds (loading chart available u...

EHD V-Booms are the strongest mount in their class. They are designed to hold maximum loads in most wind speeds (loading chart available ...

These mounts allow Microwave Dishes to be mounted to the face of a tower. The kits come in a variety of face pipe sizes and lengths and i...

Used to stand off and support single antennas. It mounts to straight or tapered leg towers and works with 1-1/2" to 5" OD round legs and ...

Can be used as a simple stand off or sidearm and is capable of mounting to straight sections 1-1/2" - 5" OD and 2" x 2" to 3-1/2" x 3-1/2...

This pipe mount has an open taper adjustable bracket that allows a safety climb cable to pass through the mount. This mount works with st...

A pipe mount that allows a variety of items to be mounted fairly close to the leg of a tower. Mounts to straight or tapered tower legs, r...

This universal microwave mounting kit allows a microwave antenna to be mounted to a tower leg. Mounts to straight or tapered tower legs, ...

Specifically used for mounting small dish type antennas to Sabre 1200 TLWD, 1800 TLWD, or SRWD. Dish mount and hardware for attachment to...

Specifically used for mounting a single antenna 3' or 6' from the tower leg of a Sabre 1200 TLWD, 1800 TLWD or 1800 SRWD. Sidearm and ha...

Heavy Duty Sidearm, 6, With (1) 4" x 4' 0" Mounting Pipe, Fits Straight Leg From 1-1/2" to 5-9/16" Round Leg and 3' to 5' Tower Face Widths

Allows a place for the microwave strut to tie back to at the proper angle along the face of a tower. This mount works with straight or ta...

Used to attach round members perpendicular to other round members. Each kit includes one (1) plate and four (4) u-bolt assemblies.

Used to attach round members perpendicular to other round members. Each kit includes two (2) clamps and four (4) bolt assemblies

This kit mounts to a leg and provides a greater area for the microwave strut to tie back at the proper angle. This mount works with strai...

Allows a place for a microwave strut to directly tieback to the face mount dish support. Can be adjusted to mount anywhere on tower face ...

These brackets are used to mount a face pipe for strut support. This mount works with straight or tapered tower legs up to 16" OD Round, ...

Can be used to support and protect coax from falling debris between the tower attachment and the back of the microwave dish. All (3) vers...

Two brackets and associated hardware that allow two pipes to be mounted parallel to each other. (Pipe sold separately)

Small brackets can be used as a stand off from a tower leg/pipe or two can be used together to create a simple pipe mount. Fits 1-1/4" to...

These small formed pieces are used to attach strut to a pipe either vertically or horizontally. Includes clamp and u-bolt.

Provides additional support to Sector Mounts and Sidearm Mounts. All hardware for attachment to the tower mount and leg is included.

Used to anchor Tiebacks to tower legs. Hardware for attachment to tower leg is included.

Each kit includes three (3) mounts for attachment to straight or tapered tower legs from 1-1/2" to 5-9/16" OD round legs and 2-1/2" x 2-1...

Microwave Dish Face Strut Support Kit, for Guyed Towers, 3/8" x 3' x 5'-6"

MICROWAVE DISH FACE STAND OFF STRUT SUPPORT KIT, SUPPORT IS 5'-6" LONG, FITS 1-1/2" OD TO 3-1/2" OD ROUND LEGS

Large Leg Adapter Kit, Fits Round Legs from 1-1/2" to 10-3/4 OD and 60 Angel Legs from 2-1/2" to 8"x8"

Tower Face Mount Stand Off Bracket, 14" Stand Off, Fits 2-3/8" to 4-1/2" OD Pipe, Includes Hareware (pipe Sold Separately)

Double Antenna Clamp, with 2' Separation

THE M.O.V.E. (MAXIMIZE OFFSET OF VERTICAL ELEVATION) PLATFORM IS DESIGNED TO ALLOW THE MAXIMUM VERTICAL OFFSET OF YOUR ANTENNAS. THOSE A...

Sabre's best in class V-Boom series are attached to monopoles utilizing tri-collar brackets. V-Booms are designed to hold maximum loads ...

These platforms are designed with two connection levels to include kickers. Used for maximum loads in all wind and ice areas. It has opti...

These platforms are designed with a single connection level. Used for substantial loads in most 90 MPH/low ice load areas. It has options...

SQUARE LOW PROFILE PLATFORM, 12' FACE, FITS 12" - 40" MONOPOLE

Used to mount Platforms, T-Arms or Stand Offs to Monopoles or other round structures. Universal surface mounting allows for a variety of ...

For use with Low Profile Platforms. Handrails can come with or without extra pipes. (Extra pipes can be used for additional structural in...

Universal Reinforcement Kits add vertical stability and increase the allowable loading to Low Profile Platforms. Comes with a collar ring...

Designed to work on wood or steel (straight/round and tapered/multi-sided) poles from 8" to 36" diameter. Mounting face allows ?exibility...

Allows you to stand antennas or other items off of the monopole. These are to be used with collars. (Sold separately)

Designed to accommodate multiple face widths and antenna con?gurations. Each kit includes three (3) T-Arm Assemblies and the appropriate ...

Provides a secure mounting face to eliminate "pipe roll" during installation. Creates a true vertical pipe alignment and offers the flexi...

Allows for up to (6) six pipes to be mounted to a monopole or (with Antenna Separation Kit Attachments) to self-supporting tower legs.

Walkway for use with our SAF T-Arms. Allows the climber an area to stand while working on face-mounted antennas and RRU's. The walkway is...

Round T-Arm, Work Platform Assembly, One Platform Per Assembly, 10' Walkway for T-Arm Face

Monopole Dish Mount, With 4-1/2" OD x 5'3" Antenna Mounting Pipe

T-Arm Pivot, Azimuth Swivel

Used to mount antennas to various mounts (V-Booms, Platforms, Dish Mounts, SAF T-Booms, etc.) Available in various lengths and from 2-3/8...

Antenna Mounting Pipe Kits are available in a variety of lengths to meet all of your antenna mounting needs. Kit includes one (1) Antenna...

This is an angle constructed non-penetrating ballast frame roof mount that aligns multiple antennas in a single sector. Frame is designed...

Designed to provide support and protection for horizontal runs of transmission line. This product supports coax transmission lines on thr...

Sleepers are furnished with 3/4" diameter holes to accommodate Snap-In Hangers (sold separately). They are made of 4" X 4" PVC material a...

Capable of being attached to any tower face and are 12" wide with a rung spacing of 12". Each kit comes with hardware to connect to the n...

Used to climb poles and tower legs (for use with step clips). All parts are galvanized in accordance with ASTM A153. Each assembly includ...

Used to attach climbing or waveguide ladder to a tower face. The kits include a J-Bolt and either J-Clips (for angle members) or Ladder B...

WAVEGUIDE LADDER HARDWARE KIT, UNIVERSAL KIT, FOR 20' SECTIONS, FITS 1-1/2"-6" ANGLE, OR 3/4" TO 4-1/2" OD ROUND

Ladders to attach coax and fiber to the face of a tower and have 3' rung spacing. Available in two widths, 2'-3" for twelve (12) runs of ...

Designed to work with Waveguide Ladders (sold separately). Kits come complete with rungs punched with both 3/8" and 3/4" holes, spacers, ...

Used to support and protect lines from falling debris. The posts of this kit bolt directly to a concrete foundation. Each kit includes Gr...

Used to support and protect lines from falling debris. The posts of this kit are buried directly into the ground and encased in concrete....

This Grip Strut channel can be used to support and protect lines from falling debris as part of a waveguide bridge. It also has many othe...

Suspended below waveguide bridge grip strut panel, it allows transmission lines to be placed both above and below the bracket. The single...

Triple-T Trapeze, Post Mounted Triple Level, 24-Line

Provides support for grip strut channel and general support brackets. Each kit includes one (1) 3-1/2" OD pipe post with baseplate, four ...

Provides support for Grip Strut Channel and General Support Brackets. Pipe Post has a 3-1/2" OD and requires a minimum of 3'-6" pipe embe...

Used to connect guy strand to a dead man anchor block foundation. Hot-dipped galvanized with 5 to 11 holes and in various lengths ranging...

Makes guyed structures visible to birds, providing an economic means of reducing the hazard to both birds and guy strands. Manufactured f...

Dead end grips are used to terminate guy strand and are galvanized in accordance with ASTM A153.

For use to protect the guy strand from consistent rubbing and deterioration at the connection point. Meets Federal Specifications FF-T-27...

A wire rope clip is used to fix the loose end of the loop back to the wire rope. Meets Federal Specifications FF-C-450, Type 1, Class 1. ...

Dead end sleeves (ice-clips) are used to finish the ends of dead end grips and are galvanized in accordance with ASTM A153.

Turnbuckles are used to connect dead end grips and anchor heads. Also used to adjust guy tension and meets Federal Speci?cations FF-T-791...

Turnbuckles are used to connect deadend grips and anchor heads. Also used to adjust guy tension and meets Federal Specifications FF-T-791...

For use on the tower end of guy strand as a termination to the tower lug. Meets the performance requirements of Federal Specifications RR...

Kits contain all of the hardware components, except guy strand, required for a standard single guy strand assembly. Designed for use with...

Oversized Hex Nuts used for Anchor Bolts. Hex Nuts are galvanized in accordance with ASTMA153.

Hex Jam Nuts are galvanized in accordance with ASTM A153.

Anco Nuts are galvanized in accordance with ASTM A153.

Pal Nuts are galvanized in accordance with ASTM A153.

Flat Washers are galvanized in accordance with ASTM A153.

Lock Washers are galvanized in accordance with ASTM A153.

Bevel Washers are galvanized in accordance with ASTM A153.

Fender Washer, for 3/8" Diameter Bolt 1-1/2" OD

Each assembly includes one (1) Threaded Rod, two (2) Lock Washers, two (2) Flat Washers, and two (2) Hex Nuts. Additonal hardware combina...

Couplers are used to connect threaded rods end to end and are galvanized in accordance with ASTM A153.

Each assembly includes one (1) ASTM A36 U-Bolt, two (2) ASTM A563 Grade DH or A194 Grade 2H Heavy Hex Nuts, two (2) Flat Washers, and two...

Each assembly includes one (1) ASTM A325 Bolt, one (1) Hex Nut, and one (1) Lock Washer. All parts are galvanized in accordance with ASTM...

Used to anchor Self-Supporting Towers and Monopoles to the foundation. All parts are galvanized in accordance with ASTM A153. Each assemb...

Each assembly includes one (1) ASTM A36 J-Bolt, two (2) ASTM A563 Grade DH or A194 Grade 2H Heavy Hex Nuts, one (1) Flat Washer, and one ...

Uni-Strut, Used to attach Equipment that is 1-5/8" x 1-5/8" x 10'

For use in downloads, grounding rings, etc. Supplied on reels or in coils. Order either 250' or 500' lengths.

Ground rods are used for terminating grounding into soil. Available in copper, copper clad, galvanized steel, and in diameters of 5/8" an...

24" long Gate Jumpers can be used with Universal Pipe Clamps (sold separately) or can be exothermically welded to gates and/or fences.

Available in 5/8" or 3/4" diameter with a 2" threaded bottom. Each kit includes one (1) Lightning Rod, two (2) Hex Nuts, two (2) Flat Was...

Allows the attachment of a Cable Safety Climb System (sold separately) on pipe and solid round tower legs with step bolts. All kits come...

Allows the attachment of a Cable Safety Climb System (sold separately) or Cable Guides (sold separately) on pipe and solid round tower le...

These systems meet or exceed performance requirements for the latest OSHA specifications and ANSI recommendations. They provide an ideal ...

Allows the attachment of a Cable Safety Climb System (sold separately) on pipe and solid round tower legs with step bolts. All kits come ...

These systems meet or exceed performance requirements for the latest OSHA specifications and ANSI recommendations; and provide an ideal m...

Used for many different applications and available in bulk 20' lengths. From 2" x 2" x 3/16" angle, 20' long to 3" x 3" x 5/16" angle, 20...

Used for many different applications and available in bulk 21' lengths. From 2-3/8" OD pipe, 21' long to 4-1/2" OD pipe, 21' long.

Constructed of the same foliage as the replica tree branch and wraps around the face of the antenna. Made of extremely durable materials,...

Adaptable to most manufacturers' branch receptors, the Monopine Replacement Branch is made of extremely durable materials and offers the ...